How To Connect Jbl 9.1 Soundbar
The JBL BAR 9.1 comes with everything you need to install, set upwards and optimise it in the box, only before we get on to the good stuff, a quick gripe: the included ii-pin ability cables for the soundbar and subwoofer are ludicrously short at 0.9m. So, unless your power sockets are fortuitously shut to both units – mine weren't – yous're going to need to replace them with longer cables.
That moan aside, everything you need to accept a fully-functioning 5.1.iv sound system is nowadays and correct. Bated from the 'bar, sub and rears, there'south besides an HDMI cable, and the aforementioned side caps. There's too a template and wall mounts for the soundbar, along with mounts for the rear speakers that you can hook them on to when they're in use and unhook them when y'all want to recharge them.
Everything y'all need to ready and optimise the BAR 9.1 is in the box, even if the power cables are ludicrously short
In terms of placement, brand certain the upwardly-firing drivers aren't being blocked and for the all-time results y'all'll need a reflective ceiling. JBL recommend sitting between 2.5 and 3m from the main unit, and a ceiling elevation of nearly 3m. For best results make sure the surround speakers are just behind you, and at about ear level. The sub should go at the front of the room, in either the left or correct hand corner.
In terms of connections, you can attach the soundbar directly to the HDMI-ARC input on your Idiot box using the provided cablevision. If your Tv doesn't support ARC, you'll need to apply the optical digital connectedness. If your TV supports eARC, y'all might too connect all your sources directly to the Tv because you can send lossless sound dorsum via HDMI-ARC. That arroyo too makes sense if your TV and 4K disc player both support HDR10+, but if your Goggle box doesn't back up eARC (or you take a lot of sources) you can use the HDMI input on the bar instead.
If you want to connect a Bluetooth device simply press the dedicated push on the remote and pair the two. If yous want to connect a different Bluetooth device, printing and hold the Bluetooth button for three seconds, this will clear the previous device and allow you to pair the new one. To connect to your home network, you lot tin either apply a wired Ethernet connection or set a wireless connection using the Google Home app or AirPlay for iOS devices. Both are straightforward, and by doing this y'all can not only enjoy the benefits of Chromecast and AirPlay 2, only you can also easily update the BAR ix.i's firmware, although when doing this the rear speakers must be attached to the primary unit.
Once everything is connected and you've powered upwards the system, the subwoofer should wirelessly connect automatically (although this tin can also be done manually if the two demand reconnecting). The rear speakers will accept three hours to fully charge, and should also connect to the main unit automatically when detached. There is the option to charge the rear speakers without connecting them to the primary unit by using Micro USB, only initially you lot need to adhere the speakers to the chief unit so they wirelessly connect.
Unlike a lot of soundbar manufacturers, JBL has included an automatic audio calibration feature
When the rear speakers are charged and connected, place them on either side of the seating position (sweet spot), and press and hold the HDMI push on the remote for 5 seconds. There's a countdown from five to one, before the audio calibration starts. When 'Calibration-i Done' is displayed, the calibration of the listening zone is successfully completed.
Then place the rear speakers in their desired position, and press and hold the HDMI button on the remote again for five seconds. Once again in that location will be a inaugural from five to one, earlier the second sound calibration starts. When 'Scale-2 Done' is displayed, the calibration of the position is successfully completed.
This is a great feature, and something of a rarity with very few soundbar manufacturers offering an automated audio scale feature. The Atmos setting defaults to center, but you can choose low or high if you lot experience you're non getting plenty of an result. The same goes for the Rear setting, and the Bass setting defaults to 3 but yous tin can go down to 1 or up to 5, depending on the depression frequency response of your room.
The Smart mode is the default setting, and this automatically applies processing to non-Atmos/DTS:X content. If you'd rather apply the Standard way which applies no processing, press the mute button for five seconds and then '+' on remote. Conversely, if yous want to engage the Night mode and then as not to disturb others, press the mute push button for five seconds and then '-' on remote. Notation that the BAR ix.ane will revert dorsum to Smart mode every fourth dimension it's turned off or in standby.
A few other useful dual controls on the remote include checking the battery accuse on the rear speakers by holding the mute push for 5 seconds and then pressing the Atmos button on the remote. You tin can restore the factory settings by holding down the power and source buttons on soundbar for more 10 seconds. Finally, if you want to know which software version your Bar 9.one is running without using Google Dwelling, hold downwardly the source and volume downward buttons simultaneously for 10 seconds and it'll appear on the bar'south display.
For testing I connected a Panasonic DP-UB820 4K Blu-ray player to the soundbar using the available HDMI input, while a Manhattan T3-R Freeview set-peak box was continued directly to the Idiot box and its audio sent back via HDMI ARC. The soundbar's ARC capability with Atmos was tested using the built-in Netflix and Amazon apps on an LG 77C9, and the UB820 was also connected directly to the C9 to allow lossless audio to be sent back to the BAR ix.i to test its eARC capabilities.
Source: https://www.avforums.com/reviews/jbl-bar-9-1-soundbar-review.17696/
0 Response to "How To Connect Jbl 9.1 Soundbar"
Post a Comment